WUFI Corr button does not appear

All about WUFI Pro
Post Reply
Nordlicht
WUFI User
WUFI User
Posts: 24
Joined: Tue May 17, 2011 12:37 am -1100
Location: Bremen

WUFI Corr button does not appear

Post by Nordlicht »

Hello I tried have a look at WUFI Corr but I was not able to get data into the programm.
In the help it says that after the Installation there should appear a button in the movie player simular to the WUFI Bio button. It does not on my installation.

I am using the latest Version of WUFI Pro 5.3.4.1363

Kind regards
Nordlicht
Christian Bludau
WUFI SupportTeam IBP
WUFI SupportTeam IBP
Posts: 1157
Joined: Tue Jul 04, 2006 10:08 pm -1100
Location: IBP Holzkirchen, the home of WUFI
Contact:

Re: WUFI Corr button does not appear

Post by Christian Bludau »

Dear Nordlicht,

The Animation1D of WUFI Pro 5 can only handle 3 IDs for IBP PostProcessModules.
And WUFI Corr has the internal ID 4.

To get it run go to the postproc folder of WUFI, usually here:
c:\Program Files (x86)\WUFI\PostProc\ and create a copy of the file ID_4.ini and rename it to an ID higher than 100, e.g. ID_104.ini

The open this file with the editor and change the first line from
[ID_4] to [ID_104] (if you used that).

Save and reopen Animation1D, then it should work.

Christian
Nordlicht
WUFI User
WUFI User
Posts: 24
Joined: Tue May 17, 2011 12:37 am -1100
Location: Bremen

Re: WUFI Corr button does not appear

Post by Nordlicht »

Dear Christian,

now the button is integrated in Animation 1D and it seems to work, but when WUFI Corr opens up there is no data transfered.

KR
Nordlicht
Christian Bludau
WUFI SupportTeam IBP
WUFI SupportTeam IBP
Posts: 1157
Joined: Tue Jul 04, 2006 10:08 pm -1100
Location: IBP Holzkirchen, the home of WUFI
Contact:

Re: WUFI Corr button does not appear

Post by Christian Bludau »

Right, that dosn´t work for me either.
But you can open up the WUFI Project File (w5p) in WUFI Corr using the File -> Open menu.

As WUFI Corr is developed for WUFI Pro 6 we probably will not guarantee the functionality with older versions.

Christian
Nordlicht
WUFI User
WUFI User
Posts: 24
Joined: Tue May 17, 2011 12:37 am -1100
Location: Bremen

Re: WUFI Corr button does not appear

Post by Nordlicht »

Ja, das geht, aber dann kann ich ja nur die Innenoberfläche betrachten und keine Position innerhalb der Konstruktion.

Gruß
Nordlicht
Christian Bludau
WUFI SupportTeam IBP
WUFI SupportTeam IBP
Posts: 1157
Joined: Tue Jul 04, 2006 10:08 pm -1100
Location: IBP Holzkirchen, the home of WUFI
Contact:

Re: WUFI Corr button does not appear

Post by Christian Bludau »

Was auch gehen müsste ist die ASCII-Ausgabe der Position in WUFI z.B. über einen Monitor und dann unter "Ursprungsdatei" im Ast "Temp und RF am Metall" öffnen.

Gruß,
Christian
Post Reply